How To Reset Etc On Dodge Avenger?

Published date:

2022-10-05
Score: 4.18/5 (37 votes)

Are you searching for an answer to the question: How to reset etc on dodge avenger? On this page, we've collected the most accurate and complete information to ensure that you have all of the answers you need. So keep reading!

Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.

You may wonder, how do i reset my etc sensor? Like in the old CEM, you can reset it by holding "DIMMER" button and pressing the "RESET" button for 4-5 seconds.

Similarly one may ask, how do i reset my dodge computer? To reset the computer in your RAM 1500, take the following steps:

  • Identify your battery's negative cable.
  • Disconnect the negative cable from the battery.
  • Wait 20 minutes so that all systems have shut down.
  • Reconnect the negative cable.
  • Besides above, how long does it take to reset a throttle body? Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking.

    Likewise, is there a fuse for the electronic throttle control? There isn't a fuse specifically for the electronic throttle control in the majority of most modern cars, but there is a fuse for the engine control module. The engine control module is what controls the electronic throttle control, so if that fuse blows, then the electronic throttle control will no longer work.


    What does the lightning bolt mean on a Dodge Avenger?

    The lightning bolt warning light alerts you to a fault in the electronic throttle control system in your vehicle. This may be a faulty throttle body, the throttle body sensor or possibly the throttle body control motor which is what controls the opening and closing of the throttle body as the motor requires more fuel.

    How much does it cost to fix etc light?

    To fix an electronic throttle control costs between $580-$700, including jeep electronic throttle control repair cost. A mechanic's labor costs between $100-$125, minus taxes and fees, and repairs in other parts may also be required.

    How much does it cost to reset a throttle body?

    The throttle body part will typically cost between $200 and $500, depending on the type of car that you drive. Labor costs for this kind of repair are typically relatively low, so you can expect to pay between $50 and $150 to have the part professionally installed.

    What causes ETC failure?

    The most common causes of an electronic throttle control light are a faulty throttle control sensor or a faulty throttle accelerator pedal position sensor.

    Do you have to reset computer after replacing throttle position sensor?

    After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset.

    How much does it cost to fix ETC light?

    To fix an electronic throttle control costs between $580-$700, including jeep electronic throttle control repair cost. A mechanic's labor costs between $100-$125, minus taxes and fees, and repairs in other parts may also be required.

    What does it mean when the ETC light comes on?

    This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.


    How To Reset Etc On Dodge Avenger - What other sources say:

    Need help with ETC issue | Dodge Avenger Forum?

    You can try resetting the ETC as well. Place you vehicle in the run position without starting and depress the gas pedal and release all in 2 ...

    How do i reset the 2008 Dodge Avenger throttle position ...?

    Wait for all the lights to go out; it's expected the check engine light (CEL) may remain illuminated. Slowly press down on the accelerator pedal until it's all ...

    ANSWERED: Etc light flashing (Dodge Avenger) - CarGurus.ca?

    An ECU reset will do it but that's extreme. You're better off just doing a sensor init and let it learn over 2 hours of collective driving. 8 people think this ...

    Reset electronic throttle control - Fixya?

    To do this, Turn the key to the run position with the engine off for at least three minutes.Then turn the key to the off position.Start the engine and let it ...

    Electronic Throttle Control Light On? (Here's How To Fix It)?

    5 days ago — What does the Electronic Throttle Control (ETC Light) mean on my dashboard? What causes it to come on, and is it safe to continue driving ...

    Electronic Throttle Control Light - DodgeForum.com?

    You can try resetting the ETC as well. Place you vehicle in the run position without starting and depress the gas pedal and release all in 2 seconds (1 down and ...

    Electronic Throttle Body Assembly with IAC TPS | for Dodge ...?

    Buy Electronic Throttle Body Assembly with IAC TPS | for Dodge Avenger Caliber Journey Chrysler ... In my case I didn't have to reset or reprogram anything.


    Used Resourses: